Stai usando un browser molto obsoleto. Puoi incorrere in problemi di visualizzazione di questo e altri siti oltre che in problemi di sicurezza. . Dovresti aggiornarlo oppure usarne uno alternativo, moderno e sicuro.
No Marco, come da guida e come da indicazioni di Mooch, le Sony fake hanno un solo anello.
Puoi gentilmente postare dove hai visto su Youtube il sistema di verifica? Grazie.
Specifiche del produttore per le batterie Sony VTC6 18650:
Pesata una delle mie batterie originali. Come vedi il peso è identico a quello riportato, c'è solo in più l'adesivo bianco messo dal venditore.
Inoltre si vedono i due anelli sul lato del positivo.
MXJO Yellow/Silver 35A 3000mAh 18650 Bench Test Results...only a 15A-20A battery, but near an HG2
Bottom Line: In my opinion, this is only a decent performing 15A-20A continuous discharge current (CDR) high capacity cell. Its capacity is about 12% lower than the LG HG2 and it runs a few degrees-C hotter.
Bottom Line
In my opinion, this is only a decent performing 15A-20A continuous discharge current (CDR) high capacity cell. Its capacity is about 12% lower than the LG HG2 and it runs a few degrees-C hotter.
Battery buyers should not have to go to the company's web site just to find out what the number on the wrap means. I will be testing cells at the rating listed on the wrap and pointing out when they fail to meet that listed rating. These MXJO cells failed to meet the rating on their wraps by a huge margin.
Continuous-Current Test Results
Pulsed-Current Test Results
These tests are done to show the performance of the cell at higher pulsed current levels. If you are running your mod at these levels be aware that you risk overheating, and possibly venting, the battery if there is a malfunction or accidental pressing of your mechanical mod's button.
Comments
At 10A it reached about 2750mAh. This is average performance for a 3000mAh-rated cell at 10A.
At 15A the maximum temperature reached 72°C. This is below the average temperature of a cell operating at its CDR.
At 20A the maximum temperature reached 87°C. This is 10°C above the average for a cell operating at its CDR. The capacity was 12% lower than a LG HG2 at 20A.
At 25A the temperature rose to 101°C. This is way too high for a cell operating at its CDR and is a degree above my safety limit of 100°C.
A single discharge at 35A was done to show the cell's performance at the rating on its wrap. The voltage quickly dropped to below 3.0V and the temperature skyrocketed to 119°C. This is an unsafe temperature and this is clearly not a 35A cell!
After this 35A discharge, another discharge at 20A shows the huge amount of damage done to the cell after a single discharge at 35A.
Using another cell, doing three 20A discharges showed that no damage was being done to the cell at this discharge current level.
I am setting a CDR of 15A-20A for this cell. Its temperature is too high at 20A to give it that rating. While operating any cell near its rated maximum current causes damage to the cell, I would expect decent cycle life from this cell at 15A-20A.
I have included pulsed discharges but I haven't set pass/fail standards for pulse testing yet. The discharges were done at 30A-60A, 5sec on/30sec off, down to 2.5V. One chart shows the entire discharge at each level. The other chart is zoomed in to show the first 5 minutes to make it easier to see the voltage sag at different current levels.
La mia VTC6 ne pesa 44 gr. e quindi gatta ci cova
Ora me ne sta arrivando un'altra speriamo di non prendere l'ennesima, sola.
Certo che è veramente una vergogna che siti noti si prestino a simili buggerature
Non aggiungerò più nulla al riguardo!
La mia VTC6 ne pesa 44 gr. e quindi gatta ci cova
Ora me ne sta arrivando un'altra speriamo di non prendere l'ennesima, sola.
Certo che è veramente una vergogna che siti noti si prestino a simili buggerature
Non aggiungerò più nulla al riguardo!
Infatti se devo prendere delle batterie, e a breve un paio sarò costretto a prenderle, vado in negozio fisico. E comunque non pensare siano solo le batterie, anche con i cotoni te la mettono in quel posto!
No Marco, come da guida e come da indicazioni di Mooch, le Sony fake hanno un solo anello.
Puoi gentilmente postare dove hai visto su Youtube il sistema di verifica? Grazie.
In parte è farina del mio sacco, in parte presa da un vecchio articolo della TPA, che trovo ancora oggi interessante e diventa sempre più attuale visto le normative che sono in aria, fa capire a chi ancora non lo sa, come sono fatti gli aromi, spero vi piaccia, leggetelo con calma quando avete...
Per calcolare la resistenza interna di una box bisogna avere il dado in rame, chiamato Calibration Tool for DNA200, ad oggi introvabile, parlo di questo:
il miglior strumento atto allo scopo, si trovava qui (link), oppure un filo spesso di rame per cortocircuitare un atomizzatore (usatene uno...
Un saluto a tutti ed inizio subito postandovi un video di come si è sempre lavorato un pad di Muji o cotoni organici similari:
Bene! Forse per il cloud di un tempo poteva andare anche bene come regola. Sta di fatto che se ne spreca un po' e si perde anche un bel po' di tempo a stare, con...
Ciao a tutti, stavo leggendo qua e la vari post nel forum, ad un tratto mi hanno colpito alcune righe dove si nominava la qualità dell'acciaio usata per gli ATOM.
Ho scambiato qualche parola con @Sva3d e mi son convinto a darvi qualche nozione su questo materiale.
Allora per iniziare non farò...
Una delle cose di cui parlo spesso sono le combinazioni aromatiche, l'articolo precedente ha ormai qualche annetto e andrebbe aggiornato e probabilmente lo farò, per chi non l'avesse letto, ecco il rimando...
Come promesso, eccomi a descrivere quale tipo di rigenerazione, in particolare sul cotone, ho testato in questi dieci giorni e più, sperimentando tutti i cotoni più noti (Cloud9, Bacon V2, Bacon Prime, Titanium Fumytech, Titanium Fiber Cotton, Miracle UD, Native Wicks Platinum Plus, Fiber...